Welcome!

Hi There!

This is a new blog I started to document all my 40k painting and modeling projects. It's brand new so i might not have that many posts up yet, but bear with me!

Be sure to look around for a bunch of tutorials on Terrain and Converting.

Enjoy!

- Nox

Pages

Sunday, December 29, 2013

Easy, Dirt Cheap Capillary Towers





Hey everyone! Here's a tutorial on how to make Capillary Towers from egg cartons. They're super easy to make and if you have all the materials, which most people do, then they don't cost anything!

I apologize in advance if my tutorial isn't very clear; im not always great at explaining things. but hopefully the pictures will give u a better idea than my confusing directions :)



What you'll need:
Egg carton
Q-tips
Gluegun
a small rock
a base

1). Cut the egg carton into pieces like the ones below:


2). glue the pieces together in a stack, gluing them all on one corner so the tower has a slight curve (you can vary this pretty easily) Glue some spare round pieces of the carton to the bottom to build up the base, leaving a hollow space at the bottom


3). (this is optional) Take ur small rock and glue it to the base to make the tower bottom heavy. Then place your tower onto the base, over the rock

5). For the top, roll some of the carton into a cone shape and glue it together, then glue this to the top.


4). Grab your glue gun! fill in all the gaps between the carton pieces


5). glue some lines down the inward side of the tower, to make it look all alive and alien


6). For the spikes: roll a q tip in some glue (pva glue is easier, but the gluegun is faster) the q tip will form a point after a couple of turns, but after that itll start to fall apart so dont roll it too much. Repeat.


Then cut the tip off of the q tip and glue it onto the tower, and repeat!



7). add any more hot glue to areas you think need it. Then, prime and paint!



Sunday, December 22, 2013

Nid City 2.0 - Part One




Hey guys

This is the very beginning of my big terrain project that i've nicknamed "Nid City 2.0" (2.0 because i got halfway through making a previous board and decided to restart it, after making several huge mistakes).

Basically, it's a Tyranid Infested City

I've divided the board into three parts that i will complete all the way to the end, so if i never finish the project, at the very least i'll have one third completely finished

And so, here are the first few steps, all completed! These ones  were all the boring measuring steps, so i'm glad i got most of them out of the way

For starters, i measured out all the sidewalks and bases and streets, then cut them out of MDF and glued them to... more MDF


Gonna be a lot of digestion pools, capillary towers, Tyranid egg things, tentacles ..it's gonna be crazy. For now, you sort of have to use your imagination.



Next i got started on the two digestion pools and one plain crater. Cut some triangles out of Polystyrene  then covered them with a layer of spackling paste.

I also got started on the first building - in total, there will be five buildings, one pedestrian bridge, and one giant statue.


To give you an idea of the more finished board, here's my digestion pool test. The water effect here turned out a little opaque, but you get the idea.


Alright, that's it so far! There will be a lot more exciting steps in the future - i just wanted to post the beginning of the project to get it out there.

Stay tuned for asome tutorials on ruins and buildings...

Wish me luck! Thanks for reading

- Nox

Saturday, December 21, 2013

Dead Fex!

Hey there!

Thought i'd share one of my more...uh, graphic side projects - a dead Carnifex! I've been using it as a unique objective marker / tank explosion marker. It's gotten a lot of attention when i've brought it to my local store so i thought i'd share it!





Sorry for the medium quality pictures.

Its made from greenstuff, apoxie sculpt, and some spare bitz from a Carnifex kit


Also, i'm starting up a hug project i've dubbed "Nid City" which will be a full on board of buildings, digestion pools, and hopefully more dioramas like these. So stay tuned for more progress on that!

Display Board for Art School

Thought i'd share a few pictures of the board i submitted as part of my Portfolio for applying to art school.

The board is part of my DIY Realm of Battle (check out my tutorial HERE) and i built the ruin a while ago - some tutorials on building ruins coming soon!






Pathfinder: Camo Suit Tutorial


Hey there!

Here's a quick tutorial on making a Ghillie suit for all your scout, special ops, and recon needs!

You will need:

- A model
- gauze/bandage tape (you can find them at any drug store)
- Elmer's glue
- Grass Flock

1). Build your model, obviously


2). Cut up some tape into pieces for the model's camo suit. I like to apply a big piece down the back and a small bit over the head



.

3). Mix a bit of water into your elmer's glue and brush it over the tape


(Sorry for the lack of photos here)

3). Prime and Paint your model normally - paint all the taped areas a dark green/brown

4). Apply glue/flock to the taped areas, and a few spots like the top of the gun casing. Then, once it dries, hit all the flocked areas with a brown wash.

5). Hide the model where no one will ever find it! 


Thursday, December 19, 2013

DIY "Realm of Battle"





Hey There!

Here's my tutorial on how to scratch build a "Realm of Battle" ala Games Workshop

If you don't feel like reading a whole lot, just scroll through the pictures - they should give you a good idea of how to build the board. But i included some written tips as well for those who like attention to detail

Assuming you have absolutely NO hobby materials to work with, the total cost is about 105$.

Here we go. Enjoy!

The Tutorial


*For a complete list of materials, scroll down to the bottom of this tutorial

1). Measuring

After getting your boards cut in half in whatever way you do (see materials list), Measure out your hill in a way you see fit. Here's how I did mine:






2).  Cutting

Measure the same lengths on you polystyrene boards. Make sure you cut so you have a perfect corner and one wavy side. That’s why I used the small 2’ by 2’ sheets



Cutting polystyrene can be a pain – I start by cutting with a hobby knife as deep as I can, then I poke holes through the cut with a butter knife. It should break easily and cleanly after that.






3). Anchor the foam!

With all your hills cut, glue them into place with a generous amount of hot glue.



Make sure your edges line up!



4). Carving

Using whatever saw you have, try to carve the start of a hill into each board. This step is awkward and difficult so be careful not to cut yourself. you can also use a serrated knife, but that’s also very dangerous. Knifes and saws are dangerous in general lol



5). Time to sand!

Use a power sander with the coarsest sandpaper you can find

CAUTION: Sanding polystyrene released tiny particles into the air that can hurt your lungs. Use a mask and definently do this step outside

This is the messiest and least fun step of the process. I’d HIGHLY Recommend holding a vacuum in your non sanding hand to suck up the pink dust while you sand.
Sand with the hills all in a circle like this to ensure all of your edges line up



Use a model to test if your slopes are too steep. Also. make sure to sand a section of the second level into the slope so it doesnt look like its just sitting on top of the hill




If you don’t have a power sander, you caaan do this by hand but it will be a horribly tedious experience. Fair warning. At least mount your paper on a small block so you have a good grip.

Once you've sanded the slopes, carve out some rocky texture into the plateau layer.



I REALLY should have done more, including carving some rock slabs out of the flat top of the hill, but i was lazy. I'd reccomend doing more than i did

6). Lava Pits/ other details

I love the look of the RoB pits filled with skulls, and although I didn’t have any skulls, I did something sort of similar out of cardstock:



Be sure to sand down the edges of the cardstock



Note that this method can also be used to make the Realm of Battle tiles, rocks, roads, etc.

Of course there are endless variations you can do – it’s your board after all. (Building a fortress into the side of a hill, anyone..?) But I kept it simple this time

7). Plaster - Part 1

If you bought the same size box as me, I’d recommend mixing 2/3 of it up at this step


Don’t worry about the ridges, this gives the board a lot of texture, and you’ll sand most of them down anyway.



8). Plaster – Part 2

Let dry, then sand down the plaster with coarse paper so its slightly flatter. Leave plenty of texture, however. Be sure to (very smoothly)sand down the sides!

^^Too Rough!^^

9). Plaster – Part 3

Mix up more plaster and fix up any seams between the hills and the MDF. Also, try to fix up the transition between the Lava Pits and the MDF. This is where I wish I’d had the Joint Compound, as its slightly easier to work with then the plaster in small areas.



As you can see, I didn’t quite smooth out the seam between the Lava Pits and the MDF enough. Oh well.

Sand down the second layer and double check that all the sides are smooth


10). Lay on the sand

I used about a 50:50 mix of Glue and Water. The plaster does a good job of preventing warping, but I still wouldn’t add any more water than that. You may want to add a touch of black paint so you can see where you’ve applied the glue so you don’t miss any spots. I wish I had done this


I use those black foam disposable brushes for this, not sure what they’re called

FIRST apply fine sand to the rocky outcrops. Shake each board off onto the next board so you can conserve sand.


Do the same thing with the coarser sand on the rest of the board until you’ve got the whole board covered




As you're going, blend any seams between fine sand and coarse sand with a foam brush



Once the glue has dried completely, use a dry, clean and stiff-bristled brush and lightly scrub the board to get rid of some of the half-glued grains. Don’t go crazy though

Sand any sand (huh!) off the edges if some glue spilled over

11). Seal the sand

*PLEASE IGNORE RED PAINT. Made a mistake and forgot this step. DON’T skip this step, it keep your boards from shedding sand everywhere whenever you transport them

Mix up about a 1:1:1 mix of glue, water, and your base color. I used black, but id highly recommends using something lighter and closer to your final look, otherwise your board will look really dark. I needed a couple coats of my base color to cover the black.





12). Paint!

^^Mid-Painting^^

I’d apply another slightly watered down coat of your base color over the glue/paint /water mix to make the color even

If you want to use my scheme, here’s what I did:

Dirt

Basecoat FolkArt Coffee bean – aka Dark Brown
Overbrush (Heavy Drybrush) Americana Burnt Sienna
Drybrush 50:50 Americana Burnt Sienna and Terra Cotta
Very Very Light Drybrush 1:1:1 Burnt Sienna, Terra Cotta, White

In my opinion, terrain tends to look like absolute (please do not swear) until that magical last pale drybrush, so don’t get discouraged if it doesn’t look right during the first two steps

Lava Pits (GW paints)

*The pit should always be darker towards the edges and brighter towards the middle


Basecoat Khorne Red
Overbrush Blood Red
Drybrush Blazing orange
Light Drybrush Golden Yellow
Very light drybrush Sunbusrt yellow
Tiny, tiny light dry brush skull white in some areas
Wash edges with Alizarin Crimson Wash, use a sponge or paper towel to blend wash towards middle of pit –don’t cover the whole thing though!

13). MOST IMPORTANT STEP

Paint the sides black!!! Painting the sides black makes it instantly look 100% more professional. It’s amazing.

The Final Product














So that’s my finished Project!! Obviously my method is a lot of work but the final product is super sturdy and neat looking


Shopping List

Home Depot/Large Home Improvement Store

(3) 1/4 inch MDF boards (2'x4') 24$ total
     -If you don't have the tools to easily cut these in half, many large home improvement stores like Home Depot will do it for you before you leave store
     -DONT get MDF thinner than this, because although it’s lighter, it ALWAYS warps. It’s horrible.

Big bag of Sand 5.00$
     -Find this in aisle near concrete

Fast Set Lite 20 (powdered plaster) 5.00$
     -Find this in section with drywall materials

*Opt: All purpose Joint compound or maybe spackling paste 5.00$
    -Find near fast set lite 20 or near spackling pastes
    -I didn’t use this for this particular project but wish I had. Good for touching up small areas after you've used the plaster. You'll see what I mean

Polystyrene  about 25$
(4) 1" thick 2'x2" sheets if they have them
(1) 1" 8'x4' sheet if not

  * This is the pink foam you always see terrain tutorials using. It can be hard to track down but MOST warehouse stores like Home Depot carry it. When buying large sheets, transport can be an issue, so if you can convince them to cut it along with the MDF boards this really helps. Sometimes they won't and you may get funny looks

Local Hardware store

White "Elmer’s" Glue 32. Oz. 12.00$
  -When I asked if they had this at Home Depot they told me it didn't exist. Ok dude...

Sandpaper – coarse ?$

Michael's/Craft or hobby store

Matte Board aka 2mm card aka the thicker version of cereal box cardboard 5.00$
 -You may have some of this lying around but it’s cheap to buy

Small bag Fine Decorative Sand 5.00$

*OPTIONAL: Paints

  -This is only if you want to copy my scheme. If not, just do yourself a favor and NEVER, NEVER use GW paints to paint a game board. That will cost you more than a realm of battle itself.

  -Please excuse my random brand choices. It’s a long story.

  -If you're shopping for paint at a craft store, paint quality from best to worst: Ceramacoat, Americana, Folkart, Craftsmart. Not sure about other brands. Most of these are only good for drybrushing, BTW

Craftsmart "Black" 16 oz. 4.00$
Folkart "Coffee Bean" 8 oz. x 2 8.00$
Americana "Burnt Sienna" 2 oz. x 3 3.00$
Americana "Terra Cotta" 2 oz. x3 3.00$
Craftsmart "White" 2 oz. 1.00$


Tools

Hot Glue Gun
Power Sander, sandpaper
Hobby Knife
Butter Knife
Saw
Paintbrushes
Scissors
Gas mask/cheap paper mask from hard wear store
Bucket for plaster

(this list might be incomplete…)




In Conclusion



What do you think? Was this tutorial helpful? There are a lot of methods to making a board (and I have tried a LOT of them) and this one has worked best for me. Hope I had some helpful tips to help other beginners avoid the mistakes that I made!

Thanks for reading

-nox